UniFi Enterprise 48 PoE Switch 720W

The Enterprise 48 PoE (USW Enterprise 48 PoE) is a fully managed switch with (48) 2.5GbE, 802.3at PoE+ RJ45 ports, (4) 10G SFP+ ports, and a 720W total PoE supply. Along with its Layer 3 functionality, this switch offers an extensive suite of Layer 2 switching protocols, including port-specific operation modes (switching, mirroring, or aggregate).The USW Enterprise 48 PoE also features a 1.3" LCM color touchscreen that concisely displays key system and connection insights.

Additionally, the USW Enterprise 48 PoE offers enhanced power supply failure protection when connected to the SmartPower Redundant Power System (USP RPS sold separately). This switch can be monitored or configured from anywhere with the powerful, intuitive UniFi Network web application and mobile app.

Features

• (1) 1.3" LCM color touchscreen with AR switch management
• (48) 2.5GbE, 802.3at PoE+ RJ45 ports
• (4) 10G SFP+ ports
• (1) USP RPS DC input
• 720W total PoE supply
• Layer 3 switching features

Dahua 5MP TiOC PoE Bullet Camera

Dahua (DH-IPC-HFW3549T1P-AS-PV) TIOC Full Colour PoE Bullet Camera. Features 5MP AI Active Deterrence, Fixed 3.6mm lens (This is the best lens for the bullet camera as it gives a longer range of view), Built-in Mic & Speaker, IP67, POE and Wizsense.

What is WizSense

WizSense is a collection of AI products and solutions that adopts independent and deep learning algorithms. With these algorithms, Dahua supports intelligent functions, such as perimeter protection and smart motion detection. In addition, the camera has excellent low light picture quality with full-color technology.
 

Features:

• 3 year return to Australia Warranty
• Dimensions: 288.4 mm × 94.4 mm × 84.7 mm
• Net Weight: 1kg
• Wizsense
• Full Colour
• 3.6mm lens. This is the best lens for the bullet camera as it gives a longer range of view.
• 5MP, 1/2.7” CMOS image sensor, low illuminance, high image definition
• Outputs max. 5MP (2592 × 1944) @20 fps, and supports 4MP (2688 × 1520) @25/30 fps
• H.265 codec, high compression rate, low bit rate
• Built-in warm illuminator, and the max. illumination distance: 40 m
• ROI, SMART H.264+/H.265+, flexible coding, applicable to various bandwidth and storage environments
• Rotation mode, WDR, 3D DNR, HLC, BLC, digital watermarking, applicable to various monitoring scenes
• Intelligent detection: Intrusion, tripwire (support the classification and accurate detection of vehicle and human)
• Abnormality detection: Motion detection, video tampering, scene changing, audio detection, no SD card, SD card full, SD card error, network disconnection, IP conflict, illegal access, and voltage detection.
• Supports sound and light alarm linkage. When an alarm is triggered, the camera links sound alarm and light flashing.
• Supports one-tap disarming. You can disarm the events of alarm output, sending email, audio, and light in the configured period.
• Alarm: 1 in, 1 out; audio: 1 in, 1 out; supports max. 256 G Micro SD card, built-in Mic and speaker
• 12V DC or PoE (802.3af)
• IP67 protection
• SMD Plus
• Red and blue flashlight alarm
• Works with the Dahua NVR's, but can also run in stand alone mode (no NVR) or you can use the software to use your computer HDD as an NVR.

Smart LAN & WiFi, 2 Channel Relay & Switch

This device has:

• 3 network Interfaces:
  • A LAN (Ethernet) interface: Connects to a Local Area Network (LAN) using a standard Cat5e/Cat6 cable.
  • A WiFi (Client) interface: Connects wirelessly to a nearby Access Point (AP)
  • A WiFi (AP) interface: Devices such a smart phones, laptops, ... can connect wirelessly.
  Note: This product can not bridge or route between interfaces.
• Two relays: These can be remotely controlled. They operate independently, and have three operational modes:
  1. Latching: Stays ON or OFF until next command.
  2. Jogging: Switches relay state (ON/OFF) for a chosen interval. e.g. ON->OFF->ON or OFF->ON->OFF.
     Interval: 0.1 to 25.5 sec in 0.1 sec increments.
  3. Delay: Same as Jogging, except:
     Interval: 1 to 65535 sec in 1 sec increments.
• Two switch inputs: The current state is always reported via the management interfaces. Optionally, these inputs can control the relay(s).
  The inputs are either:
  1. ON: Input shorted to Ground, or
  2. OFF: Input left Open circuit (there is a pull-up resistor), or raised to the same voltage used to power the device.

Features

• Three (3) Network Interfaces. All 3 network interfaces (LAN, WiFi-AP, WiFi-Client) can operate at the same time. Only one is needed to be operational.
• Static or Dynamic (DHCP) network configuration. Network configuration can be set statically, or from a local DHCP server. Operates across router boundaries if gateway/DNS IP addresses are set; this means it can be managed from any location in the world.
• Powerful WebGUI This device has a built-in web server giving the user full control via any web browser.
• Integrates with IoT platforms. MQTT is built in to this device, so it can communicate with most IoT platforms such as HomeAssistant and openHAB
• Schedules. The device includes powerful relay control based on set times. Times can be based on Time of Day, Date, and/or Day of Week.
• Network time. The device sets the date/time using Network Time Protocol (NTP). The default NTP server is: pool.ntp.org
• Mounting options. The rear includes a standard DIN rail mount. In addition, there are 4 holes for screw mounting.
• IP watchdog. Relay control based on Ping timeouts to specified IP addresses.

This product is in stock now, pricing and availability here...

UniFi Switch 8 - 60W - OEM

The UniFi POE Switch 8 port model features a compact, sleek industrial design, 4 gigabit RJ45 ports and 4 auto sensing IEEE 802.3af PoE ports that can deliver up to 15.4W of power per port. This UniFi switch is fully manageable, offers non-blocking throughput switching performance and is perfect for adding ethernet ports to your network while keeping your PoE device powered. With a switching capacity of 16Gbps, the UniFi Switch can simultaneously process traffic on all its ports at line rate without experience any packet loss.

The switch can either be mounted vertically or horizontally in any direction, providing you flexibility to install your UniFi Switch any way that suits you. If the switch is mounted on a desktop or flat surface, the design features non-skid rubber feed to hold the unit in place. Hardware is also included if your unit will be wall mounted. For added peace of mind, there is also a security slot on the side of the UniFi Switch for a padlock.

OEM packaging

These units are Brand New. They have been repackaged into boxes with packing material. The Quick Start Guide (QSG) is not included. The QSG can be downloaded from here.

Why buy through us?